@article { author = {Giasodin, Ali and Shojaosadati, Seyed Abbas and Vasheghani Farahani,, Ebrahim}, title = {Modification and Optimization of Chitin Extraction from Shrimp Shell}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {1-9}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {In the present research, extraction of chitin from shrimp shell was optimized. The optimized parameters consisted of temperature, reaction time and sodium hydroxide and hydrochloric acid concentrations in extraction processes including demineralization and deproteinazation. In literature, deproteinazation process before demineralization is reported, but our research revealed that the deproteinazation process after demineralization will result in higher yield. According to results, the best time and concentration for hydrochloric acid in the demineralization process are 8 h and 55 °C, respectively. The best time and concentration for sodium hydroxide in deproteinazation process are 12 h and 65 °C, respectively. We found that in the process of demineralization, use of 3N hydrochloric acid instead of 4N, 25% less uses of HCl. For the deproteinazation process 3N sodium hydroxide is the best concentration.}, keywords = {Modified chitin extraction,Shrimp shell,demineralization,Deproteinization}, title_fa = {اصلاح و بهینه سازی فرایند استخراج کیتین از پوست میگو}, abstract_fa = {در این پژوهش استخراج کیتین از پوسته میگو طی فرایندهای املاح ‌زدایی و پروتئین ‌زدایی از نظر زمان اقامت، غلظت مواد فراوری کننده یعنی هیدروکلریک اسید و سدیم هیدروکسید و دمای واکنش، بهینه‌ سازی شد. در برخی  از روش‌های موجود مرحله پروتئین ‌زدایی مقدم بر املاح ‌زدایی است، ولی آزمایش‌های انجام شده بیانگر این واقعیت است که فرایند املاح ‌زدایی باید مقدم بر پروتئین ‌زدایی باشد. مطابق آزمایش‌های انجام شده، دما و زمان بهینه در فرایند املاح ‌زدایی به ترتیب °C 55 و 8 ساعت تعیین شد و دما و زمان اقامت بهینه در فرایند پروتئین ‌زدایی به ترتیب °C 65 و 12 ساعت به دست آمد. در فرایند املاح‌زدایی، هیدروکلریک اسید با غلظت 3 نرمال به جای اسید 4 نرمال قابل استفاده است که موجب 25% صرفه ‌جویی در میزان هیدروکلریک اسید می‌ شود. برای فرایند پروتئین‌ زدایی، سدیم هیدروکسید با غلظت 3 نرمال به عنوان مقدار بهینه تعیین شد. در این شرایط، راندمان استخراج کیتین به حدود 82 درصد رسید.}, keywords_fa = {بهینه‌سازی,استخراج کیتین,پوست میگو,املاح زدایی,پروتئین زدایی}, url = {https://www.nsmsi.ir/article_7513.html}, eprint = {https://www.nsmsi.ir/article_7513_dac0d579847b2de59360d25d1a59945d.pdf} } @article { author = {Mayeli, Nader and Talaeipour, Mohammad}, title = {Enzymatic Deinking of Old Newspaper with Cellulase and Lipase}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {11-20}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {Biotechnical methods have the potential to offer significant improvements for traditional pulp and paper manufacturing processes due to their specificity and possible environmental advantages. Current deinking processes use large amounts of expensive, potentially environmentally damaging chemical which makes the method expensive and highly environmentally damaging. The use of enzymes could be an attractive alternative to chemicals in deinking. This research was carried out to study the influence of enzymatic deinking on optical properties and mechanical strengths of old newspaper deinked pulps. In order to perform this research, we did pulping operation with cellulase and lipase enzyme, in 4% consistency for 2.5 minutes in neutral PH, in two temperatures of 20 °C and 50 °C. After we made the pulps, we started deinking process by washing on the sieve having 120 meshes. Following this, we did statistical analyses the effect of enzymatic andtemperature treatment on optical properties and mechanical strengths of shandsheets. Results got from measuring optical properties showed that enzymatic deinking of papers leads to brightness promotion and reduces the dirt count and dirt area of handsheets. The highest brightness level and lowest dirt count and dirt area were observed in repaired samples having cellulase in 50 °C. For handsheets made from control pulp the values of folding endurance, TEA, elongation, brightness, dirt count and dirt area were 3, 34.625 J/m2, 1.74 %, 42.46 %, 51 and 1.008 mm2, respectively. On the contrary, for enzyme treated pulps the optimum values of folding endurance, TEA, elongation, brightness, dirt count and dirt area were 4, 51.54 J/m2, 2.03 %, 43.91 %, 15 and 0.245 mm2, respectively. This investigation showed that enzymatic deinking can be a suitable alternative instead of current deinking in paper recycling industries.  }, keywords = {Enzymatic deinking,Old newspaper,Cellulase,Lipase,Optical Properties,Mechanical Strengths}, title_fa = {جوهرزدایی آنزیمی کاغذ روزنامه باطله با سلولاز و لیپاز}, abstract_fa = {در این پژوهش تأثیر جوهرزدایی آنزیمی (جوهرزدایی زیستی) بر روی ویژگی‌های نوری و مکانیکی کاغذ ساخته شده از خمیرکاغذ جوهرزدایی شده از کاغذ روزنامه باطله مورد بررسی گرفت. به این منظور پس از تهیه نمونه ‌ها، عملیات خمیرسازی با دو تیمار آنزیمی سلولاز و ترکیب سلولاز/لیپاز، در درصد خشکی 4%، به مدت 5 /2 دقیقه، در pH خنثی و در دو دمای 20 و 50 درجه سانتی ‌گراد انجام شد. پس از تهیه خمیر کاغذها، مرحله جوهرزدایی به روش شستشو بر روی الک با مش 120 انجام گردید و کاغذهای دست ساز ساخته شد. در ادامه، اثر تیمارهای آنزیمی و دما بر ویژگی های نوری و مکانیکی کاغذهای دست ساز ساخته شده مورد بررسی و تجزیه و تحلیل آماری قرار گرفت. نتیجه ‌های به دست آمده از اندازه‌ گیری‌ها نشان داد که، جوهرزدایی آنزیمی به ویژه در دمای 50 درجه سانتی ‌گراد، سبب بهبود ویژگی‌های نوری و مکانیکی کاغذهای دست‌ ساز تهیه شده نسبت به نمونه شاهد شده است. برای نمونه شاهد مقاومت به تاخوردگی کاغذ 3، جذب انرژی کششی 2J/m 625/34، افزایش طول 74 /1 %، درجه روشنی %46/42، تعداد لک 51 و سطح لک 2mm 008/1 اندازه ‌گیری شد. درحالی که بیشترین مقدارها برای نمونه ‌های تیمار شده به ترتیب 4، 2J/m51 /54، % 03/2، % 91/43، 15 و 2mm 245/0 به ‌دست آمد. این پژوهش نشان داد که با توجه به محدودیت منابع چوبی در کشور از یک سو و پایین بودن سطح فناوری بازیافت در کشور از سوی دیگر، می‌توان از تیمار آنزیمی به ‌عنوان یک فرایند جایگزین فرایندهای شیمیایی مخرب محیط زیست در صنایع بازیافت کاغذ استفاده کرد.}, keywords_fa = {جوهرزدایی آنزیمی,کاغذ روزنامه باطله,سلولاز,لیپاز,ویژگی های نوری,مقاومت های مکانیکی}, url = {https://www.nsmsi.ir/article_7533.html}, eprint = {https://www.nsmsi.ir/article_7533_d800d438f6458282483c197a4b188692.pdf} } @article { author = {Froqnia, Amir and Pishvaie, Mahmoud Reza and Amin Shahidy, Babak}, title = {Control and Optimization of Oil Production Using Natural Gas Lift}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {21-28}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {This paper presents a method for controlling and optimization of an oil production system using natural gas lift concept. The process of natural gas lift consists of commingled production of an oil bearing formation with a gas bearing formation. In this process, gas is entered to oil well in a controlled manner.  Ever-increasing development of Smart Well technology and various applications of downhole monitoring and controlling instruments along with new methods of data transmission make it possible the natural gas lift system to be controlled and optimized more effectively and faster than before. With this technology it is possible to monitor the downhole conditions of gas and oil zones and to control the inflow valves in gas and oil zones. In this work, a Proportional Integral Differential (PID) feedback controller has been used to smartly control the entrance of gas from gas zone to oil well. The optimization of this process to determine the optimum setpoint of controller has been done by Differential Evolution method.}, keywords = {Auto gas lift,Natural gas lift,In-situ gas lift,PID feedback controller,Smart well,Real time optimization,Differential Evolution Algorithm}, title_fa = {کنترل و بهینه‌سازی تولید نفت با فرازآوری طبیعی گاز}, abstract_fa = {این مقاله روشی برای کنترل و بهینه‌سازی یک سامانه تولید نفت با فرازآوری طبیعی گاز ارایه می‌دهد. فرایند فرازآوری طبیعی با گاز شامل تولید هم زمان از یک مخزن نفتی و یک مخزن گازی است. در این فرایند، گاز فرازآور از ناحیه گازی به صورت کنترل‌شده وارد سامانه تولید نفت می‌شود. گسترش روزافزون فناوری چاه‌های هوشمند و در کنار آن به کارگیری گسترده ‌ی ابزار اندازه‌گیری و کنترل درون چاهی به همراه روش‌های نوین انتقال و اخذ داده باعث شده است که کنترل سامانه‌‌های فرازآوری طبیعی با گاز به مراتب مؤثرتر و به‌روزتر انجام گیرد.با این فناوری امکان بازبینی شرایط درون چاهی مانند فشار ناحیه گازی و کارآیی این ناحیه و نیز امکان کنترل درون چاهی مانند کنترل شیرهای جریان درون چاهی در ناحیه گازی فراهم می‌آید. در این بررسی، از یک کنترل‌کننده پسخور از نوع تناسبی- انتگرالی - مشتقی برای کنترل تزریق گاز استفاده شده و بهینه‌سازی این سامانه برای تعیین مقدار مقرر نرخ تزریق گاز، با روش تکامل تفاضلی انجام گرفته است.}, keywords_fa = {خودفرازآوری,فرازآوری طبیعی گاز,فرازآوری درجای گاز,کنترل‌کننده پسخور PID,چاه هوشمند,بهینه‌سازی به‌هنگام,الگوریتم تکامل تفاضلی}, url = {https://www.nsmsi.ir/article_7534.html}, eprint = {https://www.nsmsi.ir/article_7534_de66bcecf45d1de7c2c96b8553e26207.pdf} } @article { author = {Hosseini, Seyed Hossein and Zivdar, Morteza and Rahimi, Rahbar}, title = {Investigation of Solid Hold-Up in a Gas-Solid Fluidized Bed at High Gas Velocities by CFD}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {29-41}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {Simulation results of bubbling gas-solid fluidized bed using two-fluid model integrating the kinetic theory of granular flow are presented. Results of solid hold-up at different axial locations and radial directions are shown. Simulations are performed at high gas velocities. Particle motion and bubble behavior at two gas velocities of 0.35 and 0.9856 m/s in the bed are predicted and compared with the experimental data. Predicted results show that the gas velocity and ratio of the static bed height to width of the bed are important parameters for prediction of solid particles motions in a bubbling fluidized bed. Current work indicates the sensitivity of the CFD results to the drag model. Arastoopour’s drag model is the best choice for this study.At high gas velocity of 2.1824 m/s the standard k-e turbulent model and laminar models are compared. In general, the model predictions are in a good agreement with the experimental data. Current model reduces simulation’s errors compared with previous works. The minimum error is 8 % and the maximum error is 13.7 % in lower and upper part of the bed in radial direction, respectively.In addition, the error in axial direction is 4.5 %. The gas velocity values has a significant effect in solid particles motions.}, keywords = {Solid hold-up,CFD,Fluidized bed,Two-fluid model}, title_fa = {شبیه‌سازی ناپایای بستر شارانیده حبابی حاوی ذره های نوع B با استفاده از CFD در سرعت‌های بالای گاز}, abstract_fa = {بستر شارانیده گازـ جامد حبابی با استفاده از مدل دو سیالی و تئوری سینتیکی جریان دانه‌ای برای مطالعه ماندگی ذرات جامد در جهت محوری و شعاعی در سه مقطع (h/H) 25/0، 58 /0 و 89/0، شبیه‌سازی شده است. شبیه‌سازی‌ها در سرعت‌های بالا انجام شده است. حرکت ذره‌ها و رفتار حباب‌ها درون بستر، پیش‌بینی ‌شده و با نتیجه ‌های تجربی و یافته‌های دیگر پژوهشگران مقایسه شده است. نتیجه‌ ها نشان می‌دهند که رفتار ذره ‌های جامد به سرعت گاز و نسبت قطر بستر به ارتفاع ایستایی آن بستگی دارد. نتیجه ‌های مدل به ‌شدت به مدل دراگ حساس است. مدل دراگ ارسطوپور بهترین نتیجه‌ ها را در سامانه ‌ی مورد بررسی از خود نشان می‌دهد. در سرعت ظاهری گاز m/s  1824/2، مدل درهم  k-eو جریان آرام برای فاز پیوسته استفاده شده و نتیجه ‌های این دو مدل با هم مقایسه شده‌اند. به‌ طور کلی مدل موجود تطابق قابل قبولی با نتیجه ‌های تجربی داشته و بهبود چشم‌گیری در کاهش خطا نسبت به کارهای گذشته را نشان می‌دهد. خطای محاسبه شده در این مطالعه در جهت شعاعی کمترین 8 درصد در بخش پایینی بستر، بیشترین 20 درصد در بخش بالای بستر و در جهت محوری 5 /4 می‌باشد.}, keywords_fa = {هیدرودینامیک,بستر شارانیده‌ حبابی,CFD,مدل دو سیالی}, url = {https://www.nsmsi.ir/article_7535.html}, eprint = {https://www.nsmsi.ir/article_7535_557981a8106a9b1f1d3c68dfc685a2c4.pdf} } @article { author = {Hasanvand, Amin and Hashemabadi, Sayed Hasan}, title = {CFD Simulation of Pre-Polymer Pneumatic Conveying and Calculation of their Saltation Velocity}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {43-52}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {In the present study saltation velocity of particles during pneumatic conveying was calculated by Computational Fluid Dynamic (CFD). The Lagrangian approach was used for particle motion. The optimum condition in pneumatic conveying is achieved by minimum energy loss. The gas and particle motion equations were solved using a finite volume discretisation and Runge-Kutta schemes respectively. The results of CFD simulations and experimental correlation for uniform particles are in good agreement (average error 17.6%). In order to study the effect of Particle Size Distribution (PSD) on saltation velocity the real PSD of injected pre- polymer into gas phase polymerization reactor was used.}, keywords = {Pneumatic conveying,CFD,Euler/Lagrange approach,Gas solid flow,Saltation velocity}, title_fa = {شبیه سازی CFD انتقال نیوماتیک ذرات پرپلیمر و محاسبه سرعت ته نشینی آنها}, abstract_fa = {در این پژوهش سرعت ته نشینی ذرات پرپلیمر هنگام انتقال نیوماتیک با استفاده از دینامیک سیالات محاسباتی (CFD) به‌ دست آمده است. شبیه ‌سازی با استفاده از دیدگاه اولرین ـ لاگرانژین انجام شده است. برای حل عددی معادله ‌های حاکم بر سامانه انتقال نیوماتیک در حالت پایا از روش حجم محدود برای فاز پیوسته و روش رانگ کوتا مرتبه پنجم برای فاز ناپیوسته استفاده شده است. مقایسه نتیجه ‌های به دست آمده از شبیه ‌سازی با رابطه تجربی موجود برای محاسبه افت فشار در خطوط انتقال نیوماتیک نشان می ‌دهد که سرعت ته نشینی پیش ‌بینی شده توسط شبیه‌ سازی CFD به‌ طور متوسط 6/17درصد نسبت به رابطه تجربی خطا دارد. تأثیر افزایش سرعت ظاهری گاز بر  افت فشار و همچنین تأثیر در نظر گرفتن توزیع اندازه ذره‌ ها بر سرعت ته نشینی مطالعه شده است. نتیجه ‌های به دست آمده از شبیه ‌سازی CFD نشان می ‌دهد که با در نظر گرفتن توزیع اندازه ذره ها، سرعت ته ‌نشینی و افت فشار خط انتقال افزایش می ‌یابد.}, keywords_fa = {انتقال نیوماتیک,شبیه سازی CFD,اولرین لاگرانژین,جریان های گاز جامد,ته نشینی}, url = {https://www.nsmsi.ir/article_7536.html}, eprint = {https://www.nsmsi.ir/article_7536_7b2ec27ec2a688c7ee41554fbebbcef8.pdf} } @article { author = {Pahlavanzadeh, Hasan and Roshanzamir, Hasan and Mozaffari, Sayed Hossein}, title = {Investigation of the Effect of the Application of Heat Transfer Turbulators on Heat Transfer Coefficient in Two-Phase Air-Water Flow, in Bubbly Pattern}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {53-62}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {In recent years, heat transfer enhancement technology has been widely applied to heat exchangers to be used in many industrial processes. By applying this technology, the need to increase the number of heat exchangers to receive higher heat rates can be ablated that economically is of great interest. In the present work, the application of three turbulators: Wire coil insert, low density matrix insert and high density matrix insert in two-phase air-water flow was investigated. The results show that these turbulators have increased the heat transfer coefficient by 26.48, 37.52 and 59.12 percentage, respectively. By comparison, there has been seen a 13.89 percentage of deviation between the experimental and choosed reference data. Moreover, from the experimental data for that abovementationed system of Insert-applied two-phase air-water flow, separately, certain new correlations were attained and evaluated.}, keywords = {Two-phase flow,Heat transfer turbulators,Heat transfer coefficient,Turbulency}, title_fa = {بررسی تأثیر به کارگیری افزاینده های انتقال حرارت برضریب انتقال حرارت در جریان دوفازی آب ـ هوا در الگوی حبابی}, abstract_fa = {در سال‌های اخیر فناوری ازدیاد انتقال حرارت به ‌طور گسترده ای در مبدل های حرارتی برای استفاده در فرایندهای گوناگون صنعتی به‌کار گرفته می ‌شود. با استفاده از این فناوری نیاز به افزایش تعداد مبدل های حرارتی در یک مجموعه برای رسیدن به نرخ‌های حرارتی بالاتر قابل رفع می باشد که این امر از نظر اقتصادی بسیار دارای اهمیت است. در این پژوهش عملکرد سه نوع افزاینده انتقال حرارت فنر مارپیچ، ماتریس با دانسیته کم و ماتریس با دانسیته زیاد، در جریان دوفازی آب ـ هوا در الگوی حبابی مورد بررسی قرار گرفت. نتیجه‌ های به ‌دست آمده نشان دهنده آن است که افزاینده ‌های به‌ کار گرفته شده به ترتیب به میزان 48/26 ، 52 /37 و 12/59 درصد موجب افزایش ضریب انتقال حرارت شده ‌اند. مقایسه داده ‌های ضریب انتقال حرارت دوفازی آزمایشگاهی در الگوی حبابی و در لوله خالی با داده های مرجع انتخاب شده حاکی از میزان انحراف 89 /13 درصد می‌ باشد. همچنین برای محاسبه ضریب انتقال حرارت جابجایی سیال دوفازی درلوله خالی و لوله های مجهز به افزاینده، جداگانه از داده های آزمایشگاهی، رابطه ‌های جدیدی استخراج شده و مورد ارزیابی قرار گرفته است.}, keywords_fa = {جریان دوفازی,الگوی جریان حبابی,افزاینده‌های انتقال حرارت,ضریب انتقال حرارت,اغتشاش}, url = {https://www.nsmsi.ir/article_7537.html}, eprint = {https://www.nsmsi.ir/article_7537_64f7a9d0aa2b4ce4850710393f76b36b.pdf} } @article { author = {Mousavi Safavi, Seyed Mahmoud and Manteghian, Mehrdad and Vafaie Sefty, Mohsen}, title = {Study of the Methane Hydrate Stability Under Various State of Temperature and Pressure}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {63-70}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {Since The stability of methane hydrate is vital for storage and transport of natural gas, the effects of temperature and initial gas content on the dissociation rate of methane hydrate have been investigates. In order to formation of hydrate with various initial gas contents, the formation experiments have been accomplished in different condition. After formation of hydrate, the dissociation experiments have been performed at atmospheric pressure, different temperatures (ranging from 270.2 K to 262.2 K) and various initial gas  in hydrate (n0=0.03 & n0=0.06). In constant temperature, the results show that the dissociation rate and instability of hydrate decreases, because an ice layer covers the hydrate surface. This phenomenon is called self-preservation effect of gas hydrate. Also the dissociation rate decreases with reduction of temperature. Increase in the initial gas content in hydrate, results in the increment of the dissociation percentage of hydrate, since the quantity of ice has been reduced in the system. A model has been developed for prediction of methane hydrate dissociation percent by correlating the experimental data received from the related experiments.  }, keywords = {Methane hydrate,stability,Decomposition,Modeling}, title_fa = {بررسی پایداری هیدرات متان در شرایط مختلف دما و فشار}, abstract_fa = {از آنجا که پایداری هیدرات گاز متان برای ذخیره‌سازی و انتقال گاز طبیعی بسیار مهم می ‌باشد، اثر دما و مقدار مول اولیه گاز در هیدرات بر روی سرعت تجزیه هیدرات متان مورد بررسی قرار گرفته است. ابتدا هیدرات متان در شرایط گوناگون تشکیل شده تا شمار مول‌های اولیه گاز موجود در هیدرات متفاوت باشند. بعد از تشکیل هیدرات، آزمایش‌های تجزیه در فشار جو، دماهای گوناگون (K 2/270 الیK 2/264) و شمار مول‌های اولیه متفاوت در فاز هیدرات ( 06/0 و 03/0= n0 ) انجام شد. نتیجه‌ ها نشان می‌ دهد که در دمای ثابت با گذشت زمان به ‌علت تشکیل یک لایه یخ بر روی سطح هیدرات، سرعت تجزیه و ناپایداری هیدرات کاهش می‌ یابد. این پدیده اثر خود حفاظتی هیدرات نامیده می‌ شود.همچنین با کاهش دما از میزان تجزیه هیدرات کاسته شده و هیدرات، پایداری بیشتری از خود نشان می‌ دهد. با افزایش شمار مول اولیه گاز متان در هیدرات در دمای ثابت به‌ علت کاهش مقدار یخ موجود در سیستم و درنتیجه مقاومت حاصل از آن، درصد تجزیه هیدرات افزایش می‌ یابد.همچنین از برازش داده‌های آزمایشگاهی یک مدل برای پیش بینی درصد تجزیه هیدرات متان به ‌دست آمده است.}, keywords_fa = {هیدرات متان,پایداری,تجزیه,مدل سازی}, url = {https://www.nsmsi.ir/article_7538.html}, eprint = {https://www.nsmsi.ir/article_7538_934b6f083ee7d9f09d9b4a9db5aaccc3.pdf} } @article { author = {Alizadeh, Reza and Abedini, Soudeh and Nabi Bidhendi,, Gholamreza and Amoabediny, Ghasem}, title = {Removal of Lead from Battery Manufacture Industry Wastewater by Magnetite Iron Nano Particles}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {71-77}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {Lead is one of heavy metals.This toxic metal  has more application in several industry for example, battery manufacture ,tetraethyl lead manufacture , armament, paint    manufacture. This wastewaters are more toxic and  they vacate  are more hazardous for environment ,in this paper benefical of magnetite iron nano particles  pollution of lead  decreased up to standard (0.5ppm)andby alteration of chemical and phisycal parameters determined foremost term for adsorption of lead  namely, PH, concentration of magnetite iron nano particles, temperature and designed freundlich and langmuir  diagrams . at the end showed  diagram industrial application .result of this research detect high removal percent of lead(70%) in the PH =5.5-6.}, keywords = {Removal of lead,Battery manufacture industry,Magnetite iron nano particles,Wastewater treatment,environment}, title_fa = {حذف فلز سرب از پساب صنایع باتری‌سازی با استفاده از نانوذرات مغناطیسی آهن}, abstract_fa = {فلز سرب از فلزات سنگین است که کاربردهای زیادی در صنایع گوناگون باتری‌ سازی،  رنگ ‌سازی، تولید تسلیحات نظامی و ... دارد. به ‌دلیل سمی بودن این فلز، تخلیه پساب‌های صنعتی حاوی آن خطرات جبران ‌ناپذیری برای  محیط زیست و اکوسیستم‌های زنده در پی خواهد داشت. در این پژوهش با سنتز و استفاده از نانو ذرات مغناطیسی آهن ابتدا آلودگی سرب پساب ساختگی مورد بررسی قرار گرفته و سپس پساب کارخانه باتری ‌سازی به ‌عنوان نمونه مورد آزمایش قرار گرفت .همچنین با تغییر پارامترهای فیزیکی و شیمیایی همچون pH، دما،میزان نانو ذرات  و غلظت اولیه سرب  منحنی های همدمای جذب فروندلیچ و لانگمویر رسم شد. نتیجه ‌های این پژوهش بیانگر درصد حذف بالای سرب از پساب واقعی(با راندمان 70 درصد) در pH اسیدی(6-5/5) و دمای محیط می‌ باشد. برای کاربرد صنعتی این روش نیز  طرح پیشنهادی ارایه شده است.  }, keywords_fa = {حذف سرب,باتری سازی,نانو ذرات مغناطیسی آهن,تصفیه پساب,محیط زیست}, url = {https://www.nsmsi.ir/article_7539.html}, eprint = {https://www.nsmsi.ir/article_7539_97ff185c34b387c028835bb307b192f1.pdf} } @article { author = {Tavakoli, Hossein and Asghari, Manouchehr}, title = {Removing of Hydrogen Fluoride (HF) Gas from N2 and HF Mixture with NaF Pellets}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {79-84}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {This report describes adsorption of hydrogen fluoride gas in a tower containing sodium fluoride pellets by using gas mixture of hydrogen fluoride and nitrogen. At the initial time of the adsorption all of the entering hydrogen fluoride was adsorbed by the tower. Adsorption of hydrogen fluoride gas on pellets is reversible. The pellets in hot conditions were regenerated without sufficient physical deterioration. Maximum loading of adsorbent is 5.96% by weight of sodium fluoride pellets. Due to low rate of adsorption kinetic, breakthrough curve is wide.  }, keywords = {Fluorine,Hydrogen fluoride,Sodium fluoride,Packed tower}, title_fa = {حذف گاز هیدروژن فلورید از مخلوط نیتروژن و هیدروژن فلورید توسط جذب با قرص های سدیم فلورید}, abstract_fa = {در این پژوهش از طریق عبور مخلوط گازهای HF و 2N از بستر پر شده حاوی قرص‌های NaF جذب HF توسط بستر مورد بررسی قرار گرفته است. در زمان‌های اولیه عبور گاز از بستر، کلیه HF موجود در گاز توسط قرص‌ها جذب می ‌شود. به علت پایین بودن سرعت جذب، طول منحنی اشباع در بازه زمانی دیده شدن HF در گاز خروجی و اشباع کامل برج زیاد می‌باشد. ظرفیت جذب قرص‌ها در حالت اشباع کامل برابر با 96/5 درصد جرم آنها محاسبه شد. جذب HF توسط قرص‌ها برگشت پذیر بوده به‌طوری که قرص‌ها با قرار گرفتن در محیط گرم بدون اینکه دچار تخریب فیزیکی شوند کلیه HF جذب شده را آزاد می‌نمایند.  }, keywords_fa = {فلوئور,هیدروژن فلورید,سدیم فلورید,بستر پر شده}, url = {https://www.nsmsi.ir/article_7540.html}, eprint = {https://www.nsmsi.ir/article_7540_954c3b08dfebd7deea6d42b1a4b41033.pdf} } @article { author = {Masoudi, Shahram and Vafaei Softi, Mohsen and Jafari, Hamid Reza}, title = {The Investigation of Crystallization of Paraffinic Components in a Cold Flow Pipe}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {85-89}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {Transportation of a waxy oil from a cold environment leads to a decrease in the solubility of paraffinic component and formation of a deposit on the pipe wall. The observation of the deposit structure helps to study hardening process. The study shows that deposit structure is changed from plate shape to mal-crystals and spherulites during its growth. Based on the result, the diffusivity of wax deposit participated in hardening process was modified.  }, keywords = {Crystallization,structure,Paraffin,Wax,Hardening}, title_fa = {بررسی تبلور ترکیب های پارافینی در جریان نفت مدل در لوله سرد}, abstract_fa = {انتقال نفت واکس دار از نقاط سرد سبب کاهش حلالیت ترکیبات پارافینی در نفت و رسوب آنها بر دیواره لوله می‌شود. با بررسی ساختار رسوب، می‌ توان فرایند سخت شدن رسوب را بررسی نمود. بررسی ساختار رسوب در لوله نشان دادکه بلورها با رشد لایه رسوب، از ساختار صفحه‌ای به ناقص و گویچه‌ای تغییر شکل می‌یابد. با مشاهده ‌های انجام شده نسبت ابعادی بلورها در معادله پیش بینی نفوذپذیری رسوب تصحیح شد.  }, keywords_fa = {تبلور,ساختار رسوب,پارافین,واکس,سخت شدن رسوب}, url = {https://www.nsmsi.ir/article_7541.html}, eprint = {https://www.nsmsi.ir/article_7541_6e2dcf7492fc0356b45aad53980e81f1.pdf} } @article { author = {Rahbar Shamskar, Kobra and Biabani, Teyebeh and Saeidi, Mahbobeh and Alaei, Ebrahim}, title = {The Effect of Poly Phosphate Salts and Nacconol on Tricalcium Phosphate Particle Size in Its Precipitation Process}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {91-98}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {TriCalcium Phosphate (TCP) is used as suspension stabilizer in styrene polymerization process. Particle size of TCP plays an essential role in the particle size, distribution and geometric form of polystyrene product. As the particle size of TCP is reduced, there will be much better chance to surround the styrene particle. The higher the number of TCP particles surrounding each styrene particle, the lesser will be their tendency to form a large particle after collision. Therefore the percentage of spherical polystyrene with small particle size and narrow distribution in the product are increased.  In this study addition of polyphosphate salts and nacconol to the reaction mixture of TCP precipitation process and their effect on the particle size of TCP are investigated. The result show that addition of sodium hexa metaphosphate to the reaction mixture decreases the crystal growth rate and prevents precipitates to agglomerate. So the mean particles size of TCP is reduced from 5µm (without SHMP) to 1.5 µm (with SHMP).    }, keywords = {Suspension polymerization stabilizer,Tri calcium phosphate,Hydroxyapatite,Polystyrene,Beads particle size}, title_fa = {تأثیر نمک های پلی فسفات و ناکانول بر اندازه ذره های تری کلسیم فسفات در فرایند رسوب گیری آن}, abstract_fa = {در فرایند پلیمریزاسیون استایرن، تری کلسیم فسفات، TCP، به عنوان پایدار کننده سوسپانسیون پلیمر مصرف می ‌شود. اندازه ذره ‌های TCP در قدرت پایدارکنندگی آن و همچنین توزیع اندازه ذره ‌ها و شکل هندسی فراورده ‌ی پلی‌استایرن نقش بسیار مهمی را بازی می‌ نماید. هرچه اندازه ذره‌های TCP کوچکتر باشد، قدرت پوشش آن بر روی قطرات منومر استایرن افزایش یافته و میزان ادغام قطره ‌های منومر، به هنگام برخورد با یکدیگر کاهش می ‌یابد. در نتیجه درصد فراورده کروی شکل با اندازه کوچک و توزیع یکنواخت و باریک افزایش خواهد یافت. در این پژوهش، تأثیر استفاده از ترکیب‌های پلی فسفات معدنی و ناکانول بر اندازه ذره‌ های TCP که طی واکنش رسوبی کلسیم هیدروکسید و اسید فسفریک تهیه شده، مورد بررسی قرار گرفت. نتیجه‌ های به دست آمده نشان می ‌دهند که حضور سدیم هگزا متافسفات در طی واکنش رسوبگیری کلسیم فسفات، سرعت رشد کریستال‌های TCP را کاهش داده و از تجمع آن‌ها جلوگیری نموده و درنتیجه متوسط اندازه ذره ‌های فراورده از mm 5 (بدون استفاده از هگزا متافسفات) به mm 5 /1 (با استفاده از هگزا متافسفات) کاهش می‌ یابد.  }, keywords_fa = {پایدار کننده سوسپانسیون پلیمر,تری کلسیم فسفات,هیدروکسی آپاتیت,پلی استایرن,اندازه دانه‌ها}, url = {https://www.nsmsi.ir/article_7542.html}, eprint = {https://www.nsmsi.ir/article_7542_508ff13f1f45f5bbb6b850e4161ad436.pdf} } @article { author = {Ahmadianarog, Mahin}, title = {Demethylation of Methoxy- M- Terphenyls}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {1}, pages = {99-105}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {In this research work, The methoxy- m-Terphenyls are demethylated with boron tribromide  solution  in dichloromethane.The  methoxy - m -Terphenyls required , are prepared from the reaction of methoxy- aryl- grignards with 2, 6- dichloroiodobenzene in refluxing THF. The hydroxy- m- Terphenyls  can be  used for the preparing polyesters , polyethers , cyclophanes , benzoquinones  and  other derivatives of Terphenyls.  }, keywords = {: m- Terphenyls,demethylation,Aryl-Grignard,Boron tribromide solution}, title_fa = {دمتیلاسیون متوکسی متا ـ ترفنیل ها}, abstract_fa = {در این پژوهش, متوکسی متا- ترفنیل‌ها با استفاده از محلول بوران تری برمید در دی‌کلرومتان و دردما°C10- دمتیله شدند. متوکسی متا- ترفنیل‌‌های مورد استفاده شده ازواکنش متوکسی آریل ـ گرینیاردها با 2،6-دی کلرویدو بنزن درحلال THF و درحال رفلاکس تهیه شدند.}, keywords_fa = {متا- ترفنیل‌ها,متیل‌زدایی,معرف آریل گرینیارد,محلول بوران تری برمید}, url = {https://www.nsmsi.ir/article_7543.html}, eprint = {https://www.nsmsi.ir/article_7543_1943fcc686383166ac78ad048eddc8d9.pdf} }