@article { author = {Hosseinpour, Reza and Jahan-Latibari, Ahmad and Tajdini, Ajang and Sepidehdam, Sayed Mohammad Javad and Hossein, Mohammad Ali}, title = {Investigation on the Potencial of Colza Stem in Paper Production}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {4}, pages = {83-95}, year = {2012}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {This study was concentrated to investigate the influence of chemical treatment time and temperature on production of chemi-mechanical pulp from Colza stem. Three treatment times (15, 30 and 45 minutes) and two treatment temperatures (125 and 145 °C) were investigated. Chemical charge as 4% NaOH and 8% Na2SO3 as well as L/W equal to 7/1 was kept constant and high pressure cooking vessel was used. Accepted pulp yield varied between 53.8% (severe pulping) and 63% (mild pulping) and the total yield for these pulping conditions was measured between 57.6% and 68.9%. The residual lignin in low yield pulp was measured as 19% and higher yield pulp was 20.4%. Holocellulose content of pulps varied between 72.5%- 74% and freeness was between 520-590 ml CSF. Fiber quality analysis using Fiber Quality Analyzer (FQA) showed that average fiber length of pulps are between 0.54-0.65 mm, fine content is high and fiber coarseness is between 0.21-0.41 mg/m. Even though the pulp freeness was reduced from original value to about 300 mL CSF as pulps were refined in PFI mill applying 500 revolutions, but the fiber quality did not change. Measurement of fiber classification using Bauer-McNett procedure revealed similar results to FQA. Brightness was measured between 31.86- 43.38%, opacity above 99% and transparency between 4.86- 7.16%, which did not change as the pulps were refined. Strength properties of paper from these pulps before and after refining were also measured. The unrefined strength including tensile index, burst index and tear index were measured as 15.48- 26.13 N.m/g, lower than 1 kPa.m2/g and 2.91- 4.34mNm2/g respectively. These indices after treatment in PFI mill (500 revolutions) were raised to 19.74-35.19 N.m/g, 1.70 kPa.m2/g and 3.21- 4.68 mNm2/g respectively.  }, keywords = {Colza,Chemi-Mechanical,Yield,Optical,Strength,fiber Length,Coarseness}, title_fa = {بررسی پتانسیل ساقه کلزا در تولید کاغذ}, abstract_fa = {در این پژوهش ساخت خمیر کاغذ شیمیایی ـ مکانیکی از پسماند کلزا انجام گرفته است. فراوری شیمیایی در دو دمای 125 و 145 درجه سانتی‌ گراد و زمان‌های 15، 30 و 45 دقیقه و در مقدار مصرف ثابت 4 درصد سدیم هیدروکسید و 8 درصد سدیم سولفیت در یک محفظه پخت تحت فشار انجام شده است. بازده قابل‌قبول بین کمینه ‌ی 8 /53 درصد در شدیدترین شرایط پخت تا بیشینه ‌ی 63 درصد در ملایم ترین شرایط پخت اندازه گیری و  بازده کل بین 6 /57 درصد تا 9/68 درصد اندازه‎گیری شد. میزان لیگنین باقی مانده در خمیر کاغذ با بازده کمتر معادل 19 درصد و بازده زیادتر برابر با 4/20 درصد بود. هولوسلولز خمیر کاغذ نیز بین 5 /72 درصد تا 74 درصد و درجه روانی قبل از پالایش بین 520 تا 590 میلی لیتر استاندارد کانادایی اندازه ‌گیری شد. تحلیل کیفی الیاف با استفاده از دستگاه تحلیل‌ گر کیفیت الیاف (FQA) نشان داد که میانگین طول الیاف خمیر کاغذ بین 54/0 تا 65 /0 میلی متر، میزان نرمه‌ ها زیاد و زبری الیاف بین 21/0 تا 41/0 میلی‌گرم بر متر است. درجه روانی خمیر کاغذ پس از 500 دور پالایش در پالایشگر PFI به حدود 300 میلی ‌لیتر استاندارد کانادایی رسید، ولی تغییر چشمگیری در کیفیت الیاف آن دیده نشد. طبقه بندی الیاف با استفاده از غربال‌های بوئر- مکنت نیز نتیجه ‌های همانند تحلیل کیفی الیاف را نشان داد.روشنی خمیر کاغذ بین کمینه ‌ی 86 /31 درصد تا بیشینه ‌ی 38/43 درصد، ماتی بیش از 99 درصد و شفافیت بین 86 /4 تا 16/7 درصد متغیر بود، که در اثر پالایش تغییری در آن ایجاد نشد. شاخص مقاومت در برابر کشش خمیر کاغذهای پالایش شده بین N.m/g 47/15 تا 14/26 اندازه ‌گیری شد که بعد از پالایش به N.m/g 74/19 تا 19/35 افزایش یافت. شاخص مقاومت در برابر پاره شدن خمیر کاغذهای پالایش شده بین /g2m.Nm 91/2 تا 34/4 و پس از پالایش/g2m.Nm 21/3 تا 68/4 اندازه‎گیری شد.شاخص مقاومت در برابر ترکیدن خمیر کاغذهای پالایش نشده کمتر از /g2kPa.m 1 بود، که پس از پالایش به بیشترین مقدار یعنی /g2kPa.m 70/1 افزایش یافت. }, keywords_fa = {کلزا,شیمیایی ـ مکانیکی,بازده,ویژگی نوری,میانگین طول الیاف,زبری,ویژگی مقاومتی}, url = {https://www.nsmsi.ir/article_7457.html}, eprint = {https://www.nsmsi.ir/article_7457_61622f7670a2e04f44ba6502a6abd78a.pdf} }