@article { author = {Sadeghzadeh Namavar, Ali and Moghaddas, Jafarsadegh}, title = {Influence of Injection Angle in a Jet Mixer}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {30}, number = {2}, pages = {53-60}, year = {2011}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {Nowadays, most of the mixers are going to be replaced by jet mixers due to the some benefits. So investigation of the effective parameters is important in these mixers. In this article, the effect of nozzle diameter on different flow rates and effect of angle of jet injection were studied experimentally. The results showed  that   for a cylindrical tank with the shape factor of  h/D=1 and injection from center of its roof  in a constant flow rate as the nozzle diameter was increased, the mixing time was increased but the rate of increasing was decreased as flow rate was increased. Moreover the results showed that mixing time was also depended on angle of injection. Injection whit 20 and 30 degree from center of roof had the longest jet length. But injection angle 10 and 45 degree had the least mixing times. Some disagreement with the results of mixing time due to the jet length was observed when compared with those reported in the literature.  }, keywords = {Mixing,Jet mixers,Mixing time,Angle of injection}, title_fa = {اثر زاویه تزریق در اختلاط جتی}, abstract_fa = {امروزه مخلوط‌کننده‌های جتی به علت داشتن برتری‌هایی در حال جایگزینی با سایر مخلوط‌کننده‌ها در بعضی از کاربردهای صنایع شیمیایی می‌باشند. از این‌رو بررسی پارامترهای تأثیرگذار در این مخلوط‌کننده‌ها دارای اهمیت می‌باشد. در این پژوهش، تأثیر قطر نازل در شدت‌های حجمی‌ متفاوت جریان جت‌شونده و تأثیر زاویه تزریق جت، به‌طور آزمایشگاهی مورد مطالعه قرار گرفته‌اند. نتیجه ‌های آزمایشگاهی نشان‌ دهنده آن است که برای یک مخزن استوانه‌ای با ضریب شکل برابر یک (1=h/D ) و تزریق جت از مرکز سقف مخزن، افزایش قطر نازل در یک جریان حجمی ثابت منجر به افزایش زمان اختلاط می‌شود، ولی روند بیشتر شدن با افزایش شدت حجمی جریان جت‌شونده، تضعیف می‌شود. همچنین نتیجه‌ ها نشان می‌دهند که زمان اختلاط به زاویه تزریقجت بستگی دارد. تزریق با زاویه 20 و30 درجه از مرکز سقف مخزن، دارای بلندترین طول‌های جت می‌باشند، که بر اساس پژوهش‌های انجام شده قبلی، مبنی بر کاهش زمان اختلاط با افزایش طول جت، کوتاه‌ترین زمان‌های اختلاط را نتیجه نمی‌دهند. این درحالی است که زاویه‌های تزریق 10 و45  درجه دارای کمترین زمان اختلاط می ‌باشند.}, keywords_fa = {اختلاط,مخلوط‌کننده‌های جتی,زمان اختلاط,زاویه تزریق}, url = {https://www.nsmsi.ir/article_7519.html}, eprint = {https://www.nsmsi.ir/article_7519_630baf0ed18fe55f349ef38d51817b63.pdf} }