@article { author = {Mohammadian Gezaz, Somayyeh and Heydarian, Hamed and Barghamadi, Mohammad}, title = {Study on the Polymerization, Curing, and Mechanical Properties of Unsaturated Polyester Nanocomposite: Effect of Monomers Ratio and Nanosilicate Concentration}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {40}, number = {2}, pages = {1-14}, year = {2021}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {In this study, after the preparation of unsaturated polyester with various ratios of anhydride monomers, the effects of nanosilicate on the polymerization, curing behavior, and mechanical properties were investigated. The unsaturated polyester resin was synthesized at various molar ratios of anhydride monomers (maleic/phthalic: 10 to 90%) and propylene glycol. Acid number measurement was used to evaluate polymerization. With an increase in the molar maleic content, the time of polymerization reaction and the acidic number increased. In the next step, the resin was cured with an accelerator and initiator, and styrene monomer. curing behavior was determined using a curing curve and gelation time measurement. The curing curve showed that by increasing the maleic anhydride monomer ratio from 10% to 90%, the curing time decreased by 77%, and the maximum thermogenic temperature increased by 24%. Increasing the maleic content from 10 to 90% resulted in tensile strength changes from 11 to 70 MPa and tensile modulus from 60 to 359 MPa. The impact strength and the heat distortion temperature increased and became plateaued at higher maleic percentages. The nanocomposites were prepared with 50 mol% maleic anhydrides, containing 2, 4, 6, and 8 wt.% of nanosilicate. By increasing the amount of nanoclay, the curing time decreased and the maximum exothermic temperature increased. Mechanical properties were evaluated by using Heat Deflection Temperature (HDT), tensile properties, impact strength, and surface hardness tests. The impact strength and the heat distortion temperature also showed an upward trend with an increase in the amount of nano, even in small quantities. By adding 8% nanoclay to the matrix, the impact strength and heat deflection temperature increased by 11% and 13%.}, keywords = {Esterification,Anhydride ratio,Nanosilicate,Curing,Mechanical properties}, title_fa = {بررسی ویژگی های پلیمرشدن، پخت و رفتار مکانیکی نانوکامپوزیت پلی استری غیراشباع: اثر نسبت مونومرها و غلظت نانوسیلیکات}, abstract_fa = {در این پژوهش،  پس از تهیه پلی استر غیراشباع با نسبت­ های گوناگون مونومرهای انیدریدی، مقدارهای گوناگون نانوسیلیکات به پلیمر افزوده شد و رفتار پخت و ویژگی­ های مکانیکی نانوکامپوزیت بررسی شد. طی واکنش استری شدن، رزین پلی­ استرغیراشباع با استفاده از نسبت ­های مولی گوناگون مونومرهای انیدریدی (مالئیک بر فتالیک به نسبت­های 10 تا 90 درصد) با پروپیلن گلیکول سنتز شد. برای بررسی پیشرفت پلیمریزاسیون از روش اندازه ­گیری عدد اسیدی استفاده شد. با افزایش درصد مولی مالئیک انیدرید، زمان واکنش پلیمریزاسیون و رسیدن به عدد اسیدی دلخواه افزایش یافت. در مرحله بعد، پخت رزین­ انجام شد. رفتار پخت با استفاده از نمودار پخت و اندازه ­گیری زمان ژل شدن تعیین شد. نمودار پخت نشان داد که با افزایش نسبت مونومر مالئیک از 10 تا 90 درصد، زمان پخت 77% کاهش و دمای بیشینه گرمازایی 24% افزایش یافت.  افزایش مقدار مالئیک انیدرید از 10 تا 90 درصد، سبب تغییر استحکام کششی از 11 به 70 مگاپاسکال و مدول کششی از 60 به 359 مگاپاسکال شد. استحکام ضربه و دمای خمش گرمایی نیز روند افزایشی نشان داد و در درصدهای بالای مالئیک ثابت شد. در ادامه، نانوکامپوزیت­ ها در مقدار مالئیک انیدرید  50% مولی، دارای 2، 4، 6 و 8  درصد وزنی از نانوسیلیکات تهیه شدند. با افزایش مقدار ذره های نانو سیلیکات، زمان پخت پلی استر غیر اشباع کاهش و دمای بیشینه گرمازایی افزایش یافت. بررسی ویژگی­ های مکانیکی با استفاده از آزمون­ های دمای خمش گرمایی، ویژگی­ های کششی، مقاومت ضربه و سختی سطحی انجام شد. افزایش نانوذره ها بهبود ویژگی­ های کششی را در پی داشت. ویژگی­ های استحکام ضربه و دمای خمش گرمایی نیز با افزایش مقدار نانو حتی در مقدارهای کم، روند افزایشی نشان داد. به­ طوری که با افزودن 8 درصد نانورس به زمینه، استحکام ضربه و دمای خمش گرمایی به ترتیب به میزان 11 درصد و 13 درصد افزایش یافت.}, keywords_fa = {استری شدن,نسبت انیدریدها,نانو سیلیکات,پخت,ویژگی‌های مکانیکی}, url = {https://www.nsmsi.ir/article_36830.html}, eprint = {https://www.nsmsi.ir/article_36830_f56cf56ccce4a54b1337e50d5ad20a19.pdf} }