@article { author = {Farshi Azhar, Fahimeh and Olad, Ali and Jafarpour, Maliheh}, title = {Preparation of Nanocomposite Systems Based on Natural Polymers and Clay for Controlled Release of Cisplatin}, journal = {Nashrieh Shimi va Mohandesi Shimi Iran}, volume = {40}, number = {4}, pages = {1-19}, year = {2022}, publisher = {Iranian Institute of Research and Development in Chemical Industries (IRDCI)-ACECR}, issn = {1022-7768}, eissn = {}, doi = {}, abstract = {In this study, after the preparation of unsaturated polyester with various ratios of anhydride monomers, the effects of nano silicate on the polymerization, curing behavior, and mechanical properties were investigated. The unsaturated polyester resin was synthesized at various molar ratios of anhydride monomers (maleic/phthalic: 10 to 90%) and propylene glycol. Acid number measurement was used to evaluate polymerization. With an increase in the molar maleic content, the time of polymerization reaction and the acidic number increased. In the next step, the resin was cured with an accelerator and initiator, and styrene monomer. curing behavior was determined using a curing curve and gelation time measurement. The curing curve showed that by increasing the maleic anhydride monomer ratio from 10% to 90%, the curing time decreased by 77%, and the maximum thermogenic temperature increased by 24%. Increasing the maleic content from 10 to 90% resulted in tensile strength changes from 11 to 70 MPa and tensile modulus from 60 to 359 MPa. The impact strength and the heat distortion temperature increased and became plateaued at higher maleic percentages. The nanocomposites were prepared with 50 mol% maleic anhydrides, containing 2, 4, 6, and 8 wt.% of nano silicate. By increasing the amount of nanoclay, the curing time decreased and the maximum exothermic temperature increased. Mechanical properties were evaluated by using Heat Deflection Temperature (HDT), tensile properties, impact strength, and surface hardness tests. The impact strength and the heat distortion temperature also showed an upward trend with an increase in the amount of nano, even in small quantities. By adding 8% nanoclay to the matrix, the impact strength and heat deflection temperature increased by 11% and 13%.}, keywords = {Esterification,Anhydride ratio,Nanosilicate,Curing,Mechanical properties}, title_fa = {تهیه سامانه های نانو چندسازه‌ای بر پایه پلیمرهای طبیعی و خاک رس به منظور رهایش کنترل شده داروی ضد سرطان سیس پلاتین}, abstract_fa = {هدف این مطالعه، توسعه سامانه رهایش کنترل شده برای داروی ضدسرطان سیس پلاتین (Cisplatin) به منظور بهبود زمان نیمه عمر و اثربخشی آن می‌باشد. سیس پلاتین در بین لایه های سیلیکاتی مونت موریلونیت سدیم (MMT) به روش بین لایه‌ای کردن محلول قرار گرفته و توسط پلیمرهای طبیعی کیتوزان (CS)، نشاسته (St) و آلژینات (Alg) احاطه می شود. به منظور بررسی اثر MMT، نانو چندسازه‌های CS/MMT/Cisplatin و St-Alg/MMT/Cisplatin با مقدارهای متفاوت MMT تهیه شدند. نانو چندسازه‌های تهیه شده با تجزیه و تحلیل­ های اسپکتروسکوپی فروسرخ تبدیل فوریه (FT-IR)، پراش پرتو ایکس (XRD) و میکروسکوپ الکترونی روبشی (SEM) شناسایی و تعیین ویژگی شدند. با آزمایش‌های برون تنی، اثر مقدار MMT و همچنین اثر pH محیط رهایش بر روی پروفیل رهایشی دارو از سامانه‌های نانو چندسازه‌ای ارزیابی شد. مطابق نتیجه‌ها، سامانه نانو چندسازه‌ای CS/MMT/Cisplatin با مقدار 50% وزنی MMT و سامانه نانو چندسازه‌ای St-Alg/MMT/Cisplatin با مقدار 30% وزنی MMT، در محیط رهایش با 4/7= pH به طور مؤثری میزان رهایش را در حد دلخواه ثابت نگه می دارد، به طوری­که زمان لازم برای رهایش 50% دارو (T50%) برای این  نانو چندسازه‌ها به ترتیب برابر با  4 روز و 14 ساعت می‌باشد. همچنین رهایش داروی سیس پلاتین در محیط به­ نسبت بازی بیش­تر از محیط اسیدی بوده و امکان مصرف خوراکی به دلیل محافظت در محیط معده وجود خواهد داشت.}, keywords_fa = {Esterification,Anhydride ratio,Nanosilicate,Curing,Mechanical properties}, url = {https://www.nsmsi.ir/article_37786.html}, eprint = {https://www.nsmsi.ir/article_37786_01e7a285832d49f7f1cca685209864c7.pdf} }