Nashrieh Shimi va Mohandesi Shimi Iran

Nashrieh Shimi va Mohandesi Shimi Iran

Thermal and Hydraulic Analysis of the Wavy-Fins-Plate Compact Heat Exchangers

Document Type : Research Article

Authors
Hanieh Ghanbar Kharghani Nejad 1
Mohammad Reza Jafari Nasr 2
1 Department of Chemical Engineering, Faculty of Engineering, Islamic Azad University, Science and Research Branch, Tehran, I.R. IRAN
2 Research Institute of Petroleum Industry (RIPI), Tehran, I.R. IRAN
Abstract
Thermo-hydraulic analysis of compact heat exchangers is strongly depended on the performance of  heat transfer surfaces. This is evaluated by Colburn and Fanning friction factors versus Reynolds number. In this paper, CFD analysis is carried on with 18 different type of wavy fins geometries. The effects of the four geometrical factors of fin; height, fin spacing, wave amplitude, wavelength over a wide range of Reynolds number  are investigated. Then a parametric study for two enhanced designs C-shaped and S-shaped sinusoidal wavy offset-strip fins is conducted. Those four geometrical factors described the wavy channel and combined and related by the parameters α, β and γ which represent the dimensionless geometrical parameters. The numerical computations are performed by solving a steady, three dimensional Navier-Stokes equation and energy equation using Ansys Fluent 15.0 software program. Air is considered as working fluid. The computational results have an adequate accuracy when compared to experimental data. The CFD simulation results reveal that the geometrical parameters of wavy fins have significant effects on the j and f factors as a function of Reynolds number.
Keywords
Compact heat exchangers
Thermo-hydraulic analysis
Colburn factor
Fanning friction factor
Wavy fins

Subjects

[1] Sheik Ismail L., Velraj R., Studies on Fanning Friction (f) and Colburn (j) Factors of Offset and Wavy Fins Compact Plate Fin Heat Exchanger-A CFD Approach, Numerical Heat Transfer, Part A: Applications, 56(12): 987-1005 (2009). 
[2] Zhang J., Kundu J., Manglik R.M., Effect of  Fin Waviness and Spacing on Lateral Vortex Structure and Laminar Heat Transfer in Wavy-Plate-Fin Cores, International Journal of Heat and Mass Transfer, 47(8): 1719-1730 (2004).
[3] London A.L., Shah R.K., Offset Rectangular Plate-Fin Surfaces–Heat Transfer and Flow Friction Characteristics, Journal of Engineering for Gas Turbines and Power, 90(3): 218–228 (1968).
[4] Patankar S.V., Liu C.H., Sparrow E.M., Fully Developed Flow and Heat Transfer in Ducts Having Streamwise-Periodic Variations of Cross- Sectional Area, Journal of Heat Transfer, 99(2): 180-186 (1977).
[5] Shah R.K., London A.L., "Laminar Flow Forced Convection in Ducts: A Source Book for Compact Heat Exchanger Analytical Data", Supplement 1 to Advances in Heat Transfer, Academic Press, New York (1978).
[6] Kays W.M., London A.L., "Compact Heat Exchangers", McGraw Hill (1984).
[7] Gough R.J., Al-Shemmeri T.T., Thermal and Friction Factor Data for Three Packed Block Construction Wavy Fin Surfaces, Journal of Power and Energy, 208(3): 225-229 (1994). 
[8] DeJong N.C., Zhang L.W., Jacobi A.M., Balachandar S., Tafti D.K., A Complementary Experimental and Numerical Study of the Flow and Heat Transfer in Offset Strip-Fin Heat Exchangers, Journal of Heat Transfer, 120(3): 690–698 (1998).
[9] Xi G., Shah R.K., Numerical Analysis of Offset Strip Fin Heat Transfer and Flow Friction Characteristics, In "Proc. Int. Conf. Computational Heat and Mass Transfer", Eastern Mediterranean University Printinghouse Gazimagusa, Cyprus, pp. 75-87 (1999). 
[10] Metwally H.M., Manglik R.M., Enhanced Heat Transfer due to Curvature-Induced Lateral Vortices in Laminar Flows in Sinusoidal Corrugated-Plate Channels, International Journal of Heat and Mass Transfer, 47(10): 2283-2292 (2004).
[11] Manglik R.M., Zhang J., Muley A., Low Reynolds Number Forced Convection in Three-Dimensional Wavy-Plate-Fin: Fin Density Effects, International Journal of Heat and Mass Transfer, 48(8): 1439-1449 (2005).
[12] Junqi D., Jiangping C., Zhijiu C., Yimin Z., Wenfeng Z., Heat Transfer and Pressure Drop Correlations for the Wavy Fin and Flat Tube Heat Exchangers, Applied Thermal Engineering, 27(11): 2066-2073 (2007).
[13] Sheik Ismail L., Ranganayakulu C., Shah R.K., Numerical Study of Flow Patterns of Compact Plate-Fin Heat Exchangers and Generation of Design Data for Offset and Wavy Fins, International Journal of Heat and Mass Transfer, 52(17): 3972-3983 (2009).
[14] Vyas S., Manglik R.M., Jog M.A., Visualization and Characterization of a Lateral Swirl Flow Structure in Sinusoidal Corrugated-Plate Channels, Journal of Flow Visualization and Image Processing, 17(4): 281–296 (2010).
[15] Khoshvaght Aliabadi M., Gholam Samani M., Hormozi F., Haghighi Asl A., 3D-CFD Simulation and Neural Network Model for the j and f Factors of the Wavy Fin-and-Flat Tube Heat Exchangers, Brazilian Journal of Chemical Engineering, 28(3): 505-520 (2011).
[16] Tao Y., He Y., Qu Z., Tao W., Numerical Study on Performance and Fin Efficiency of Wavy Fin-and-Tube Heat Exchangers, Progress in Computational Fluid Dynamics, an International Journal, 11(3): 246-254 (2011).
[17] Huzayyin O.A., "Computational Modeling of Convective Heat Transfer in Compact and Enhanced Heat Exchangers", Doctoral dissertation, University of Cincinnati, (2011).
[18] جعفری‌نصر، محمدرضا؛ سعیدان، مهسا؛ طراحی بهینه و مدل­سازی مبدل‌های حرارتی قاب و صفحه‌ای، نشریه شیمی مهندسی شیمی ایران، (4)27: 79 تا 92 (1387).
[19] Cen Z.L., ZhaoJ.G.,  Shen B.X.,A Comparative Study of Omega RSM and RNG k–ε Model for the Numerical Simulation of a Hydrocyclone, Iranian Journal of Chemistry and Chemical Engineering (IJCCE), 33(3): 53-61 (2014).
[20] FLUENT User’s Guide, Fluent Incorporated Lebanon, NH, USA. (2004).