Nashrieh Shimi va Mohandesi Shimi Iran

Nashrieh Shimi va Mohandesi Shimi Iran

The Investigation of Critical Impeller Speed in a Laboratory Mechanical Flotation Cell

Document Type : Research Article

Authors
Hosna Darabi 1
Seyed Mohammad Javad Koleini 1
Bahram Rezai 2
Mahmoud Abdollahy 1
1 Mineral Processing Dept., Tarbiat Modares University, Tehran, I.R. IRAN
2 Department of Mining & Metallurgical Engineering, Amirkabir University of Technology, Tehran, I.R. IRAN
Abstract
One of the important steps in flotation is particle collection that occurs after the successful particle-bubble interaction. Effective solids suspension is a necessary preconditioning for particle collection and flotation. The critical impeller speed, Njs, is commonly used to indicate the effectiveness of solids suspension. The critical impeller speed refers to the minimum impeller speed where all the solids are just suspended off the bottom of the cell. In this paper, two correlations for predicting the critical impeller speed in terms of particles size (dp), relative solids density (ρs-ρl), solids concentration (X), liquid viscosity (vL) and superficial gas rate (Jg) in two and three phases conditions have been developed. The study was conducted in a laboratory flotation cell using four size fractions of quartz, barite, and galena. The results indicated that ρs-ρl, dp, X and vL are the most important variables, respectively. The critical impeller speed increased linearly with increasing Jg. Investigation of concentration profiles versus the relative height of the cell showed that suspension heights consistently reached a level equivalent to 0.80-0.85 of the cell height at the critical impeller speed. Homogeneous suspension condition will only be approached as the impeller speed was increased to approximately 120–150% of the critical impeller speed. This range can be used to predict the optimum impeller speed in order to increase the flotation efficiency. 
Keywords
Laboratory mechanical flotation
Solids suspension
Critical impeller speed
Optimum impeller speed

Subjects

[1] Arbiter N., Harris C.C., Yap R.F., Hydrodynamics of Flotation Cells, SME Transactions, 244: 134–148 (1969).
[2] Yianatos J., Bergh L., Condori P., Aguilera J., Hydrodynamic and Metallurgical Characterization of Industrial Flotation Banks for Control Purposes, Minerals Engineering 14: 1033–1046 (2001).
[3] Van der Westhuizen A., Deglon D., Evaluation of Solids Suspension in a Pilot-Scale Mechanical Flotation Cell: The Critical Impeller Speed, Minerals Engineering, 20(3): 233-240(2007).
[4] Nienow A.W., The Suspension of Solid Particles, In: Harnby N., Edwards M.F., Nienow A.W. (Eds.), “Mixing in the Process Industries”, 2nd Butterworth-Heinemann, Oxford: 364–393 (1992).
[5] Ayranci I., Kresta S.M.,Critical Analysis of Zwietering Correlation for Solids Suspension in Stirred Tanks, Chemical Engineering Research and Design, 92(3):413-422) 2014(.
[6] Shahbazi B., Rezai B., The Effect of Micro Turbulence on Quartz Flotation Rate, Iran .J. Chem. Chem. Eng. (IJCCE), 34 (3): 77-87 (2015).
[7] Zwietering T.N., Suspending of Solid Particles in Liquid by Agitators, Chemical EngineeringScience, 8(3): 244-253 (1958).
[8] Dutta N., Pangarkar V., Critical Impeller Speed for Solid Suspension in Multi‐Impeller Three Phase Agitated Contactors, The Canadian Journal of Chemical Engineering, 73(3): 273-283 (1995).
[9] Van der Westhuizen A., Deglon D., Solids Suspension in a Pilot-Scale Mechanical Flotation Cell: A Critical Impeller Speed Correlation, Minerals Engineering, 21(8): 621-629 (2008).
[10] Grenville  R.K., Mak A.T.C., Brown D.A.R., Suspension of Solid Particles in Vessels Agitated by Axial Flow Impellers, Chemical Engineering Research and Design, 100(12):282-291 (2015).
[11] Nienow A., Suspension of Solid Particles in Turbine Agitated Baffled Vessels, Chemical Engineering Science, 23(12):1453-1459(1968).
[12] Baldi G., Conti R., and Alaria E., Complete Suspension of Particles in Mechanically Agitated Vessels, Chemical Engineering Science, 33(1): 21-25 (1978).
[13] Myers K.J., Fasano J.B., and Corpstein R.R. ,The Influence of Solid Properties on the Just‐Suspended Agitation Requirements of Pitched‐Blade and High‐Efficiency Impellers, The Canadian Journal of Chemical Engineering, 72(4):745-748 (1994).
[14] Ayranci I., Ng T., Etchlls III A.W.,  Kresta S.M.,Prediction of Just Suspended Speed for Mixed Slurries at High Solids Loadings, Chemical Engineering Research and Design, 91(3):227-223) 2013(.
[15] Ayranci I., Machado M.B., Madej A.M., Derksen J.J., Nobes D.S., Kresta S.M., Effect of Geometry on the Mechanisms for Off-Bottom Solids Suspension in a Stirred Tank, Chemical Engineering Science, 79: 163-176(2012).
[16] Montante G., Lee K., Brucato A., Yianneskis M., Numerical Simulations of the Dependency of Flow Pattern on Impeller Clearance in Stirred Vessels, Chemical Engineering Science, 56(12): 3751-3770(2001).
[17] Montante G., Brucato A., Lee K., Yianneskis M., An Experimental Study of Double‐to‐single‐loop Transition in Stirred Vessels, The Canadian Journal of Chemical Engineering, 77(4): 649-659 (1999).
[18] Nienow A.W., Edwards M.F., Harnby N., “Mixing in the Process Industries”, Butterworth-Heinemann (1997).